Booties 2mm SOLITE 2020 Custom Omni

Add to Wishlist


 

Our Custom Omni series answers the call where foot protection is equally critical to comfort, fit, and precise performance. The 2mm Custom Omni is our multi-sport boot intended for warmer water (60F+). To keep your feet cool, the 2mm Custom Omni features the world's first waterproof/breathable neoprene: Ventiprene, with microscopic holes that allow your feet to breath without letting water in. An O-Ring cuff seal at the top provides additional water-sealing. The 2mm Omni features 3mm thickness gum-rubber sole pods, offering added protection against rough sea-beds while still maintaining unmatched flexibility, comfort, grip and performance.

>>> WHAT'S MY BOOTIE SIZE?

Intended for use in rivers, lakes, or oceans, the 2mm Custom Omni is ideal for SUP, Canoe, Kayak, Kitesurf, Windsurf, Sailing, Whitewater Rafting, Scuba, Snorkel or any other aquatic pursuit you can think of. All custom Omni boots also have a snag-free design: no closed loops or straps anywhere that could pose an entrapment risk.

Sizing Tip: Order your regular shoe size or 1/2 size down. For example, if you are a size 10.5, order a 10. Women should order 1-1.5 sizes lower to convert from Men's sizing. So if you are a Women's 8, order a Men's 7. If you are a Women's 8.5, also order a Men's 7. NOTE: If your feet are exceptionally narrow or low volume, you may want to size down even more.

Recommended Water Temps: 60+F. 

Key Features:

  • Heat-moldable with boiling water for the perfect custom fit.
  • NEW softer-compound Thermo-Form sole for next-level comfort, warmth, dexterity, and durability.
  • Internal split-toe locks your foot inside the boot for precise response.
  • NEW super-tacky, non-marking 3mm vulcanized gum rubber sole pods for grip, protection, and flexibility.
  • 2mm waterproof/breathable Ventiprene upper with comfy flat-lock seams.
  • Abrasion-resistant Supratex II outer lining and hydrophobic quick-dry inner lining.
  • Moulded no-loop heel pull prevents snagging in kayaks.

 

HEAT MOLDING INSTRUCTIONS

Solite Boots are the world's first and only custom, heat-moldable watersports footwear. Custom fitting can be done in your kitchen with nothing more than a kettle of boiling water. To heat-mould your Solite boots, watch the video below and follow the instructions carefully. Do not use any other methods of heat moulding except boiling water. Use of ovens, microwaves, heat guns, etc. will void your warranty.

STEP-BY-STEP

1. Bring water to a boil (you will need approximately 3 cups of boiling water per boot.)

2. While water is heating, roll down the cuffs of your Solite boots and place them in a sink.

3. Put on your Solite Heat Booster socks. These socks will help allow for a little extra space when the boots are being moulded.

4. Once water comes to a full bubbling boil, gently pour into your Solite boots (in the sink), filling each to slightly below the seam where the neoprene upper is attached to the sole. See photo.

5. Wait 5 minutes for the boiling water to soften the sole material.

6. After 5 minutes, carefully pour out the hot water from your Solite boot (doing one boot at a time) and quickly rinse out the inside of the boot with cold water to lower the surface temperature and to prevent burning. Test with your hand as you will want to get your foot in as warm as you can comfortably stand.

7. Place your foot inside your Solite boot while wearing the Heat Booster sock. Make sure your big-toe sits comfortably in the toe cavity and your heel is flush in the heel pocket.

8. Repeat Steps 6 and 7 for the other boot.

9. Secure boot ankle straps if you have them.

10. Walk around in your Solite boots for the next 10 minutes as they custom mold to your feet.

11. Once your Solite Boots have cooled to room temperature, the molding process is complete.

12. If you are unhappy with the fit, you can re-mold your Solite boots repeating the same steps above. Your Solite boots should feel completely comfortable, almost like part of your foot.

 #Solite 2020 2mm Custom Omni